Has 6D IMU onboard: 3D accelerometer + 3D gyroscope
Comparison to Beacon HW v4.9:
TX-only beacon – can transmit ultrasonic, but can’t receive it. Beacon HW v4.9 is dual-use: can receive and transmit ultrasonic
Mini-TX Smaller size and lighter: 47x42x15mm & 25g vs. 55x55x33mm & 62g (or 55x55x64mm with antenna). More on comparison
Battery – 250mAh vs. 1000mAh in a regular beacon. But Mini-beacon has a new more efficient ultrasonic TX module, thus, battery lifetime in TX mode is even superior to the Beacon HW v4.9
Tested battery lifetime with 8Hz – 96h. With lower update rate – nearly proportionally longer. Very efficient ultrasonic TX module
Mini-beacon has only USB (virtual UART) output – no additional pins
Mini-beacons always have embedded IMU – newer and better, but it has 3D accelerometer and 3D gyroscope, but no magnetometer (which we do not recommend to use indoor anyway, due to magnetic field distortion indoor)
Embedded antenna – smaller size, but smaller radio coverage ~50m with regular Modem HW v4.9 as compared with ~100m of Beacon HW v4.9 with Modem HW v4.9
Range in ultrasonic is virtually on par with regular Beacon HW v4.9 – up to 30m with Beacon HW v4.9 as RX beacon. At the same time, for example, a combination of Mini-RX beacon + Mini-TX provide a better coverage and a stronger signal, than Beacon HW v4.9 + Beacon HW v4.9
This HW supports license-free 915MHz ISM band (US) and license-free SRD band 868MHz (EU), i.e. 433MHz (EU band) is not supported and not planned
No customer reviews for the moment.
error
Your review appreciation cannot be sent
feedback
Report comment
Are you sure that you want to report this comment?
check_circle
Report sent
Your report has been submitted and will be considered by a moderator.
error
Your report cannot be sent
Write your review
check_circle
Review sent
Your comment has been submitted and will be available once approved by a moderator.
Description
Not for new design. We are shipping out the last beacons from the last batch. The Beacons HW v4.9 are replaced with Super-Beacons.
Beacon HW v4.9 with 9D IMU onboard...
Description
Not for a new design. We are shipping out the last modems from the last batch. The Modems HW v4.9 are replaced with Modem HW v5.1.
Modem is a central controller of the...
SPOT Tablet
Additional tablet controller configured with Spot application
WHAT'S INCLUDED
• Tablet controller configured with Spot application and Android 8.1• Tablet case and charger...
+ Lidar for SPOT
Spot EAP enhances the range and accuracy of Spot’s autonomy system for use on large sites.
PRODUCT HIGHLIGHTS
The Spot EAP (Enhanced Autonomy Package) improves Spot’s autonomy...
+ Awareness for SPOT
Spot CAM provides a color panoramic view of the robot's surroundings and communication capabilities enabling an improved teleoperation experience.
PRODUCT HIGHLIGHTS
The...
A1 Motor
Stable and efficient, easy to maintain
FUNCTION
PARAMETER
Maximum Torque
33.5N.m
Weight
about 605g
Operating Voltage
12~30V (Recommended Voltage:24V)
Maximum Current
40A...
+ Inspection for SPOT
Spot CAM+ adds a pan-tilt-zoom (PTZ) camera to the Spot CAM to enable detailed inspections.
PRODUCT HIGHLIGHTS
The Spot CAM+ payload turns Spot into a powerful inspection...
+ Edge CPU for SPOT
Spot CORE provides dedicated processing for applications requiring on-robot computation.
PRODUCT HIGHLIGHTS
The Spot CORE is an additional processor for developers to run...
Description
Modem is a central controller of the system and must be always active, when the system is running
Modem’s HW supports up to 250 beacons – mobile + stationary – in any...
Description
Starter Set HW v4.9 is a precise indoor positioning and navigation solution for various applications including autonomous robots, autonomous drones, autonomous vehicles. It also works...
+ Ports for SPOT
Spot GXP provides regulated power and an Ethernet port for easy payload integration.
PRODUCT HIGHLIGHTS
The Spot GXP (General Expansion Payload) jump-starts payload integration...
error Your review appreciation cannot be sent